How to remove and install the Transmission Assembly on a 2011 Kia Sorento?

To remove the transmission, first disconnect the cable from the negative terminal of the battery, then drain the fluid from the transmission. Next, remove the entire air filter assembly along with the air duct, followed by the splash shield mounting bolts and shield. Disconnect the wiring harnesses from various sensors including the oxygen sensors, speedometer sensor, Transmission Range sensor, solenoid connector, speed sensor, transfer case shift motor (if equipped), and the oil temperature sensor. Disconnect the transmission fluid cooler hoses and seal their ends to prevent leakage and contamination. For 2009 and earlier 4WD models, remove the front driveshaft and the rear driveshaft. Disconnect the shift control cable and remove the starter. Then, remove the upper transmission mounting bolts and the inspection plate, followed by the torque converter-to-driveplate fasteners, ensuring to rotate the engine for access to all bolts while marking the position of the torque converter on the driveplate. Remove the front section of the exhaust system and place a transmission jack or floor jack with an appropriate saddle under the transmission, using safety chains for stability. Remove the remaining transmission-to-engine bolts, ensuring all connections are disconnected, then remove the crossmember bolts and move the transmission to the rear to disengage it from the engine block dowel pins, making sure the torque converter is detached from the driveplate. Lower the transmission with the jack, using locking pliers on the bellhousing case to prevent the torque converter from falling out, and finally pull the transmission out from beneath the vehicle, setting it aside safely. For installation, reverse the removal steps while ensuring that the drive tangs of the torque converter engage with the recesses in the automatic transmission fluid pump inner gear, confirming engagement by turning the torque converter while pushing it towards the transmission. Align the match marks on the torque converter and driveplate, install all driveplate-to-torque converter nuts before tightening any, and ensure to tighten the fasteners and mounting bolts to the specified torque. Fill the transmission with the correct type and amount of automatic transmission fluid, and adjust the shift cable and Transmission Range sensor upon completion.

Genuine 2011 Kia Sorento Transmission Assembly

Trans Assembly

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

12 Transmission Assemblies found

View related parts
2011 Kia Sorento Auto Transaxle & Torque/Conventional Assembly
Part Number: 450003BER0
$823.69 MSRP: $1149.00
You Save: $325.31 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Automatic Transaxle & Torque Converter Assembly
- Replaced by: 450003BER0R
- Part Code: 45000A
- Item Weight: 248.40 Pounds
- Item Dimensions: 36.4 x 25.8 x 24.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 450003BER0
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
More Info
Fits the following 2011 Kia Sorento Submodels:
- 2.4L - Theta 2 | Wagon - 5Door 5P, Wagon - 5Door 7P
View related parts
2011 Kia Sorento Auto Transaxle & Torque/Conventional Assembly
Part Number: 450003BBK0
$823.69 MSRP: $1149.00
You Save: $325.31 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Automatic Transaxle & Torque Converter Assembly
- Replaced by: 450003BBK0R
- Part Code: 45000A
- Item Weight: 215.20 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 450003BBK0
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
More Info
Fits the following 2011 Kia Sorento Submodels:
- 3.5L - Lambda 2 | Wagon - 5Door 5P, Wagon - 5Door 7P
View related parts
2011 Kia Sorento Auto Transaxle & Torque/Conventional Assembly
Part Number: 450003BEL0
$823.69 MSRP: $1149.00
You Save: $325.31 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Automatic Transaxle & Torque Converter Assembly
- Replaced by: 450003BEL0R
- Part Code: 45000A
- Item Weight: 205.30 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 450003BEL0
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
More Info
Fits the following 2011 Kia Sorento Submodels:
- 2.4L - Theta 2 | Wagon - 5Door 5P, Wagon - 5Door 7P
View related parts
2011 Kia Sorento Auto Transaxle & Torque/Conventional Assembly
Part Number: 450003B875
$823.69 MSRP: $1149.00
You Save: $325.31 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Automatic Transaxle & Torque Converter Assembly
- Replaced by: 450003B875R
- Part Code: 45000A
- Item Weight: 205.30 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 450003B875
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
More Info
Fits the following 2011 Kia Sorento Submodels:
- 2.4L - Theta 2 | Wagon - 5Door 5P, Wagon - 5Door 7P
View related parts
2011 Kia Sorento Manual Transmission Assembly
Part Number: 4300024790
$4120.36 MSRP: $6077.23
You Save: $1956.87 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Transmission Assembly-Manual; Transaxle
- Part Code: 43000
- Item Weight: 214.00 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4300024790
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
More Info
Fits the following 2011 Kia Sorento Submodels:
- 2.4L - Theta 2 | Wagon - 5Door 5P
View related parts
2011 Kia Sorento Auto Transaxle & Torque/Conventional Assembly
Part Number: 450003BBL0
$5760.60 MSRP: $8241.20
You Save: $2480.60 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Automatic Transaxle & Torque Converter Assembly
- Part Code: 45000A
- Item Weight: 215.20 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 450003BBL0
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
More Info
Fits the following 2011 Kia Sorento Submodels:
- 3.5L - Lambda 2 | Wagon - 5Door 5P, Wagon - 5Door 7P
View related parts
2011 Kia Sorento Auto Transaxle & Torque/Conventional Assembly
Part Number: 450003B2B0
$823.69 MSRP: $1149.00
You Save: $325.31 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Automatic Transaxle & Torque Converter Assembly
- Replaced by: 450003B2B0R
- Part Code: 45000A
- Item Weight: 203.40 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 450003B2B0
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
More Info
Fits the following 2011 Kia Sorento Submodels:
- 3.5L - Lambda 2 | Wagon - 5Door 5P, Wagon - 5Door 7P
View related parts
2011 Kia Sorento Auto Transaxle & Torque/Conventional Assembly
Part Number: 450003B2B5
$823.69 MSRP: $1149.00
You Save: $325.31 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Automatic Transaxle & Torque Converter Assembly
- Replaced by: 450003B2B5R
- Part Code: 45000A
- Item Weight: 207.30 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 450003B2B5
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
More Info
Fits the following 2011 Kia Sorento Submodels:
- 3.5L - Lambda 2 | Wagon - 5Door 5P, Wagon - 5Door 7P
View related parts
2011 Kia Sorento Auto Transaxle & Torque/Conventional Assembly
Part Number: 450003BBJ0
$823.69 MSRP: $1149.00
You Save: $325.31 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Automatic Transaxle & Torque Converter Assembly
- Replaced by: 450003BBJ0R
- Part Code: 45000A
- Item Weight: 219.20 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 450003BBJ0
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
More Info
Fits the following 2011 Kia Sorento Submodels:
- 3.5L - Lambda 2 | Wagon - 5Door 5P, Wagon - 5Door 7P
View related parts
2011 Kia Sorento Auto Transaxle & Torque/Conventional Assembly
Part Number: 450003BEP0
$823.69 MSRP: $1149.00
You Save: $325.31 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Automatic Transaxle & Torque Converter Assembly
- Replaced by: 450003BEP0R
- Part Code: 45000A
- Item Weight: 211.30 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 450003BEP0
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
More Info
Fits the following 2011 Kia Sorento Submodels:
- 2.4L - Theta 2 | Wagon - 5Door 5P, Wagon - 5Door 7P
View related parts
2011 Kia Sorento Auto Transaxle & Torque/Conventional Assembly
Part Number: 450003BES0
$5490.97 MSRP: $7855.47
You Save: $2364.50 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Automatic Transaxle & Torque Converter Assembly
- Part Code: 45000A
- Item Weight: 205.30 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 450003BES0
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
More Info
Fits the following 2011 Kia Sorento Submodels:
- 2.4L - Theta 2 | Wagon - 5Door 5P, Wagon - 5Door 7P
View related parts
2011 Kia Sorento Auto Transaxle & Torque/Conventional Assembly
Part Number: 450003B870
$823.69 MSRP: $1149.00
You Save: $325.31 (29%)
Product Specifications
- Other Name: Automatic Transaxle & Torque Converter Assembly
- Replaced by: 450003B870R
- Part Code: 45000A
- Item Weight: 219.20 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 450003B870
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
More Info
Fits the following 2011 Kia Sorento Submodels:
- 2.4L - Theta 2 | Wagon - 5Door 5P, Wagon - 5Door 7P

2011 Kia Sorento Transmission Assembly

Look no further for OEM 2011 Kia Sorento Transmission Assembly. Our website stocks an extensive selection, all priced competitively. You can rest assured that all of our genuine 2011 Kia Sorento Transmission Assembly are backed by a manufacturer's warranty and guaranteed quality. With our hassle-free return policy and speedy delivery, your shopping experience is set to be smooth and efficient.

2011 Kia Sorento Transmission Assembly Parts Questions & Experts Answers

Q: How to remove and install the Transmission Assembly on a 2011 Kia Sorento?
A: To remove the transmission, first disconnect the cable from the negative terminal of the battery, then drain the fluid from the transmission. Next, remove the entire air filter assembly along with the air duct, followed by the splash shield mounting bolts and shield. Disconnect the wiring harnesses from various sensors including the oxygen sensors, speedometer sensor, Transmission Range sensor, solenoid connector, speed sensor, transfer case shift motor (if equipped), and the oil temperature sensor. Disconnect the transmission fluid cooler hoses and seal their ends to prevent leakage and contamination. For 2009 and earlier 4WD models, remove the front driveshaft and the rear driveshaft. Disconnect the shift control cable and remove the starter. Then, remove the upper transmission mounting bolts and the inspection plate, followed by the torque converter-to-driveplate fasteners, ensuring to rotate the engine for access to all bolts while marking the position of the torque converter on the driveplate. Remove the front section of the exhaust system and place a transmission jack or floor jack with an appropriate saddle under the transmission, using safety chains for stability. Remove the remaining transmission-to-engine bolts, ensuring all connections are disconnected, then remove the crossmember bolts and move the transmission to the rear to disengage it from the engine block dowel pins, making sure the torque converter is detached from the driveplate. Lower the transmission with the jack, using locking pliers on the bellhousing case to prevent the torque converter from falling out, and finally pull the transmission out from beneath the vehicle, setting it aside safely. For installation, reverse the removal steps while ensuring that the drive tangs of the torque converter engage with the recesses in the automatic transmission fluid pump inner gear, confirming engagement by turning the torque converter while pushing it towards the transmission. Align the match marks on the torque converter and driveplate, install all driveplate-to-torque converter nuts before tightening any, and ensure to tighten the fasteners and mounting bolts to the specified torque. Fill the transmission with the correct type and amount of automatic transmission fluid, and adjust the shift cable and Transmission Range sensor upon completion.

Related 2011 Kia Sorento Parts

Alternate Year Models

2010 Kia Sorento Transmission Assembly 2012 Kia Sorento Transmission Assembly