How do you remove the front and rear bumpers on Kia Sorento?

Before taking off the front bumper of the 2009 and earlier models, you should unplug the cable of the negative terminal of the battery, set the parking brake, lift the car and support it with jackstands. Pull the wires from the fog lights if exist and then retrieved headlight housing from right or left side. When the headlight housing is now out of the way, identify the other and additional bumper cover's hidden fasteners such as the corner retaining nut and fasteners from the two sides as well. If necessary, the procedure continues with the taking off of the bumper guard lower fasteners, followed by the removal of the two access hole covers as well as the nuts located behind each of them and, finally, the separation of the bumper guard from the bumper. Then, take out the bumper seal board plastic type push pins and the seal board; next, unscrew the upper trim fasteners of the bumper cover; and also, unscrew the plastic screws found at the top of the bumper cover; now, take out the screws near the lower edge of the bumper cover; and finally, take out the middle screws of the bumper cover. Starting from the 2011 and later model year you have to take out the fasteners which is attached at the bottom end of the bumper cover, at the top ends of the radiator grille, at the rearmost vertical border of the bumper cover and the fasteners that are used to hold the upper rear edges of the bumper cover to the fender as well as you have to release the clips used in fixing the upper rear edges of the bumper Proceed and visually inspect the car using a flashlight to confirm that all the clips on the bumper cover have been disconnected, then with support remove the front bumper cover. Kickstart at the rear tail light housing, then open the lift gate and raise the weather strip, then unscrew the upper bumper cover screws where situated at the top of the bumper cover. Lift the vehicle and ensure it is properly supported on jackstands and then loosen all the lower screws that attached the bumper cover to the frame and to the wheel well liners, and the screws on each side which attached the bumper cover to the under part of the wheel wells. Flip the car and turn off the breaker while inspecting with a flashlight to ascertain that everything is disconnected from the bumper cover and then remove the bumper cover. Removal is the opposite of installation.

Genuine Kia Sorento Bumper

Bumper Fascia

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

52 Bumpers found

View related parts
Kia Sorento Rear Bumper Cover
Part Number: 86610C6210
$385.87 MSRP: $555.37
You Save: $169.50 (31%)
ADD TO CART
Product Specifications
- Other Name: Cover-Rear Bumper; Bumper Cover
- Position: Rear
- Replaces: 86610C6200
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2015-2018 Kia Sorento | 2.0L - Theta 2, 2.4L - Theta 2, 3.3L - Lambda 2 | Wagon - 5Door 5P, Wagon - 5Door 7P
View related parts
Kia Sorento Rear Bumper Lower Cover
Part Number: 86612C6500
$400.14 MSRP: $575.90
You Save: $175.76 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover-Rr Bumper LWR; Lower Cover
- Position: Lower
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2019-2020 Kia Sorento | 2.0L - R, 2.4L - Theta 2, 3.3L - Lambda 2 | Wagon - 5Door 7P
View related parts
Kia Sorento Front Bumper Cover
Part Number: 86511C6500
$404.37 MSRP: $582.00
You Save: $177.63 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover-Fr Bumper; Bumper Cover
- Position: Front
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2019-2020 Kia Sorento | 2.0L - R, 2.4L - Theta 2, 3.3L - Lambda 2 | Wagon - 5Door 7P
View related parts
Kia Sorento Front Bumper Upper Cover
Part Number: 865111U200
$319.56 MSRP: $459.94
You Save: $140.38 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover-Front Bumper Upper; Bumper Cover
- Position: Front Upper
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2009-2012 Kia Sorento | 2.4L - Theta 2, 3.5L - Lambda 2 | Wagon - 5Door 5P, Wagon - 5Door 7P
View related parts
Kia Sorento Front Bumper Cover
Part Number: 86511C6200
$412.40 MSRP: $593.55
You Save: $181.15 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover-Front Bumper; Bumper Cover
- Position: Front
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2015-2018 Kia Sorento | 2.0L - Theta 2, 2.4L - Theta 2, 3.3L - Lambda 2 | Wagon - 5Door 5P, Wagon - 5Door 7P
View related parts
Kia Sorento Front Bumper Upper Cover
Part Number: 86511C6000
$347.50 MSRP: $500.15
You Save: $152.65 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover-Front Bumper Upper; Upper Cover
- Position: Front Upper
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2015-2018 Kia Sorento | 2.0L - Theta 2, 2.4L - Theta 2, 3.3L - Lambda 2 | Wagon - 5Door 5P, Wagon - 5Door 7P
View related parts
Kia Sorento Rear Bumper Lower Cover
Part Number: 866121U500
$264.52 MSRP: $380.72
You Save: $116.20 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover-Rear Bumper Lower; Lower Cover
- Position: Lower
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2013-2014 Kia Sorento | 2.4L - Theta 2, 3.3L - Lambda 2 | Wagon - 5Door 5P, Wagon - 5Door 7P
View related parts
Kia Sorento Rear Bumper Lower Cover
Part Number: 86610C6050
$364.54 MSRP: $524.67
You Save: $160.13 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover-Rear Bumper Lower; Lower Cover
- Position: Lower
- Replaces: 86610C6000
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2015-2018 Kia Sorento | 2.0L - Theta 2, 2.4L - Theta 2, 3.3L - Lambda 2 | Wagon - 5Door 5P, Wagon - 5Door 7P
View related parts
Kia Sorento Front Bumper Upper Cover
Part Number: 865111U000
$313.57 MSRP: $451.32
You Save: $137.75 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover-Front Bumper Upper; Bumper Cover
- Position: Front Upper
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2009-2012 Kia Sorento | 2.4L - Theta 2, 3.5L - Lambda 2 | Wagon - 5Door 5P, Wagon - 5Door 7P
View related parts
Kia Sorento Front Bumper Upper Cover
Part Number: 865111U500
$422.18 MSRP: $607.64
You Save: $185.46 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover-Front Bumper Upper; Bumper Cover
- Position: Front Upper
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2013-2014 Kia Sorento | 2.4L - Theta 2, 3.3L - Lambda 2 | Wagon - 5Door 5P, Wagon - 5Door 7P
View related parts
Kia Sorento Cover-Rr Bumper
Part Number: 86610R5310
$381.34 MSRP: $548.85
You Save: $167.51 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lower Cover
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2021-2023 Kia Sorento | 2.5L-THETA-III | Wagon - 5Door 6P, Wagon - 5Door 7P
View related parts
Kia Sorento Rear Bumper Cover
Part Number: 866101U010
$280.21 MSRP: $403.30
You Save: $123.09 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover-Rear Bumper; Bumper Cover
- Position: Rear
- Replaces: 866111U010
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2009-2012 Kia Sorento | 2.4L - Theta 2, 3.5L - Lambda 2 | Wagon - 5Door 5P, Wagon - 5Door 7P
View related parts
Kia Sorento Rear Bumper Cover Upper
Part Number: 866101U510
$298.23 MSRP: $429.24
You Save: $131.01 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover-Rear Bumper,Upper; Bumper Cover
- Position: Rear Upper
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2013-2014 Kia Sorento | 2.4L - Theta 2, 3.3L - Lambda 2 | Wagon - 5Door 5P, Wagon - 5Door 7P
View related parts
Kia Sorento Rear Bumper Cover
Part Number: 866111U000
$278.05 MSRP: $400.19
You Save: $122.14 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover-Rear Bumper; Bumper Cover
- Position: Rear
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2009-2012 Kia Sorento | 2.4L - Theta 2, 3.5L - Lambda 2 | Wagon - 5Door 5P, Wagon - 5Door 7P
View related parts
Kia Sorento Rear Bumper Cover
Part Number: 86611C6500
$363.01 MSRP: $522.47
You Save: $159.46 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover-Rr Bumper; Upper Cover
- Position: Rear
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2019-2020 Kia Sorento | 2.0L - R, 2.4L - Theta 2, 3.3L - Lambda 2 | Wagon - 5Door 7P
View related parts
Kia Sorento Front Bumper Cover
Part Number: 86510C6810
$400.14 MSRP: $575.90
You Save: $175.76 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover-Fr Bumper; Bumper Cover
- Position: Front
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2019-2020 Kia Sorento | 2.0L - R, 2.4L - Theta 2, 3.3L - Lambda 2 | Wagon - 5Door 7P
View related parts
Kia Sorento Rear Bumper Upper Cover
Part Number: 86611C6000
$365.70 MSRP: $526.34
You Save: $160.64 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover-Rear Bumper,Upper; Upper Cover
- Position: Rear Upper
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2015-2018 Kia Sorento | 2.0L - Theta 2, 2.4L - Theta 2, 3.3L - Lambda 2 | Wagon - 5Door 5P, Wagon - 5Door 7P
View related parts
Kia Sorento Rear Bumper Upper Cover
Part Number: 866111U500
$416.65 MSRP: $599.67
You Save: $183.02 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover-Rear Bumper,Upper; Bumper Cover
- Position: Rear Upper
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2013-2014 Kia Sorento | 2.4L - Theta 2, 3.3L - Lambda 2 | Wagon - 5Door 5P, Wagon - 5Door 7P
View related parts
Kia Sorento Rear Bumper Cover
Part Number: 866113E510
$252.13 MSRP: $362.89
You Save: $110.76 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover-Rear Bumper; Bumper Cover
- Position: Rear
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2006-2008 Kia Sorento | High Grade, Middle Grade | 3.3L - Lambda, 3.8L, 3.8L - Lambda | 5 Door Wagon, Wagon - 5Door 5P
View related parts
Kia Sorento Cover Front Bumper Upper
Part Number: 86511R5300
$341.37 MSRP: $491.32
You Save: $149.95 (31%)
Product Specifications
- Other Name: Cover Front Bumper; Bumper Cover
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2021-2023 Kia Sorento | 2.5L-THETA-III | Wagon - 5Door 6P, Wagon - 5Door 7P

| Page 1 of 3 |Next >

1-20 of 52 Results

Kia Sorento Bumper

If you're in search of top-notch, reasonably priced OEM Kia Sorento Bumper, then you've found the perfect spot. Our website boasts an extensive inventory of Kia Sorento Bumper, all priced at the market's premier price. Rest assured, every genuine part we offer comes with a warranty straight from the manufacturer.

Kia Sorento Bumper Parts Questions & Experts Answers

Front Bumper Upper Cover
865111U200
Q: How do you remove the front and rear bumpers on Kia Sorento?
A:
Before taking off the front bumper of the 2009 and earlier models, you should unplug the cable of the negative terminal of the battery, set the parking brake, lift the car and support it with jackstands. Pull the wires from the fog lights if exist and then retrieved headlight housing from right or left side. When the headlight housing is now out of the way, identify the other and additional bumper cover's hidden fasteners such as the corner retaining nut and fasteners from the two sides as well. If necessary, the procedure continues with the taking off of the bumper guard lower fasteners, followed by the removal of the two access hole covers as well as the nuts located behind each of them and, finally, the separation of the bumper guard from the bumper. Then, take out the bumper seal board plastic type push pins and the seal board; next, unscrew the upper trim fasteners of the bumper cover; and also, unscrew the plastic screws found at the top of the bumper cover; now, take out the screws near the lower edge of the bumper cover; and finally, take out the middle screws of the bumper cover. Starting from the 2011 and later model year you have to take out the fasteners which is attached at the bottom end of the bumper cover, at the top ends of the radiator grille, at the rearmost vertical border of the bumper cover and the fasteners that are used to hold the upper rear edges of the bumper cover to the Fender as well as you have to release the clips used in fixing the upper rear edges of the bumper Proceed and visually inspect the car using a flashlight to confirm that all the clips on the bumper cover have been disconnected, then with support remove the front bumper cover. Kickstart at the rear tail light housing, then open the lift gate and raise the weather strip, then unscrew the upper bumper cover screws where situated at the top of the bumper cover. Lift the vehicle and ensure it is properly supported on jackstands and then loosen all the lower screws that attached the bumper cover to the frame and to the wheel well liners, and the screws on each side which attached the bumper cover to the under part of the wheel wells. Flip the car and turn off the breaker while inspecting with a flashlight to ascertain that everything is disconnected from the bumper cover and then remove the bumper cover. Removal is the opposite of installation.