Where is the fuel pressure sensor located and How to replace it on Kia Sedona?

The fuel pressure sensor is connected directly to the fuel line and is mounted close to the under part of the car, mostly near the right front corner of the fuel tank. Start with the removal of the cable in question with the negative terminal of the battery. The third step is to pop the fuel filler cap to allow pressure to be released inside the fuel tank to gather. Next, unbolt the second row rear seat from the left side of the car and tilt the carpet flap. Following that, the fuel pump/sending unit floor service hole cover should be deleted. Locate the fuel tank pressure sensor connector and unplugging it, afterwards, use a socket wrench to unscrew the fuel tank pressure sensor mounting nuts at the top of the fuel pump module and pulling the sensor off. Replace the O-ring/gasket as earlier to the procedure and then the fuel pressure sensor has to be bolted into place before tightening the nuts and reconnecting the electrical connector. Last of all, join the battery cable back to its position normally.

Genuine Kia Sedona Vapor Pressure Sensor

Fuel Vapor Pressure Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

3 Vapor Pressure Sensors found

View related parts
Kia Sedona Sensor-Fuel Tank Pressure
Part Number: 314352J000
$73.83 MSRP: $106.53
You Save: $32.70 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pressure Sensor, Sensor, Tank Pressure Sensor
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2015-2021 Kia Sedona | 3.3L - Lambda 2 | Wagon Long - 7P, Wagon Long - 8P
View related parts
Kia Sedona Sensor-Fuel Tank Pressure
Part Number: 31435FD500
$70.57 MSRP: $101.83
You Save: $31.26 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pressure Sensor, Sensor, Tank Pressure Sensor
- Replaces: 0K32A18211A
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2001-2014 Kia Sedona | High Grade, Low Grade, Middle Grade | 3.5L, 3.5L - Lambda 2, 3.8L, 3.8L - Lambda | Wagon Long - 7P, Wagon Long 7, Wagon Short - 7P, Wagon Short 7
View related parts
Kia Sedona Sensor-Tank Pressure
Part Number: 0K32A18211A
$74.54 MSRP: $101.83
You Save: $27.29 (27%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 31435FD500
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2001-2005 Kia Sedona | Low Grade, Middle Grade | 3.5L | Wagon Short 7

Kia Sedona Vapor Pressure Sensor

The Kia Sedona Vapor Pressure Sensor monitors the fuel tank pressure and assists in stopping the release of hydrocarbon vapors by the EVAP system, which reduces pollution and protects engine performance. Positioned on or near the fuel tank, this tiny Vapor Pressure Sensor unit in every Sedona provides live pressure information to the ECM, which shuts the vent solenoid and opens the purge valve to allow the stored vapors to flow into the intake and burn rather than vent. If the Kia computer runs its self-test and vacuum fails to reach target, the Vapor Pressure Sensor assists in producing a warning light, often indicating a loose cap or leak. Over the years, Sedona models have made use of functionally similar versions, but sensor styles and connector tabs vary, which means that each Kia may call for the particular Vapor Pressure Sensor design constructed for its production run. Clip-in or harness mounted, a faulty Sedona Vapor Pressure Sensor can misread fuel pressure, invite excess evaporation, and should be replaced as soon as possible to keep the Kia emissions system sealed.

If you're in search of top-notch, reasonably priced OEM Kia Sedona Vapor Pressure Sensor, then you've found the perfect spot. Our website boasts an extensive inventory of Kia Sedona Vapor Pressure Sensor, all priced at the market's premier price. Rest assured, every genuine part we offer comes with a warranty straight from the manufacturer.

Kia Sedona Vapor Pressure Sensor Parts Questions & Experts Answers

Sensor-Fuel Tank Pressure
31435FD500
Q: Where is the fuel pressure sensor located and How to replace it on Kia Sedona?
A:
The fuel pressure sensor is connected directly to the fuel line and is mounted close to the under part of the car, mostly near the right front corner of the fuel tank. Start with the removal of the cable in question with the negative terminal of the battery. The third step is to pop the fuel filler cap to allow pressure to be released inside the fuel tank to gather. Next, unbolt the second row rear seat from the left side of the car and tilt the carpet flap. Following that, the fuel pump/sending unit floor service hole cover should be deleted. Locate the fuel tank pressure sensor connector and unplugging it, afterwards, use a socket wrench to unscrew the fuel tank pressure sensor mounting nuts at the top of the fuel pump module and pulling the sensor off. Replace the O-ring/gasket as earlier to the procedure and then the fuel pressure sensor has to be bolted into place before tightening the nuts and reconnecting the electrical connector. Last of all, join the battery cable back to its position normally.