How do I remove and install a blower motor and Blower Motor Resistor in a Kia Sedona?

Remove the cable connecting the negative terminal of the battery from the vehicle. Lift the rear console to access the blower motor area and disconnect the blower motor's fasteners and cover if they exist or pull the insulation down at the rear glove box. Remove the electrical connectors that are related to the blower motor power. Note: Cars with self-regulating temperature system employ a power module rather than a blower motor resistor. Both are mounted and joined in similar way. Take off the mounting fasteners and pull the unit out of the heater/air conditioning housing. Removal is the exact opposite of installation. The blower motor and the blower wheel are therefore from the manufacturer in harmony and are fitted only as a unit. The electrical connector of the blower motor should be disconnected. Retrieve the blower motor mounting bolts, then take out the blower motor. Removal is the process of dismantling a system while installation is the opposite of removal. Disconnect/reduce the rear heating and air conditioning housing. Note: All models made in 2006 and later equipped with Power Mosfet and not the blower motor resistor. Both are similar in how they are installed and interfaced. Take off the rear quarter panel trim, and unplug the connector to the blower motor resistor/Mosfet. Take out the mounting fasteners and pull out the unit away from the heater/air conditioning housing. This involves the process opposite to the removal, it involves placing the plant and equipment back at their initial positions. The blower motor and the blower wheel are assembled together at the time of manufacturing and should only be replaced together. Take off the connector that provides power to the blower motor. Take off all the screws that hold the blower motor at the back of the housing. Take off the blower motor from the housing you have identified. Removal: Installation is the exact opposite of removal.

Genuine Kia Sedona Blower Motor Resistor

Heater Blower Motor Resistor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

7 Blower Motor Resistors found

View related parts
Kia Sedona Resistor
Part Number: 971283K000
$41.57 MSRP: $59.98
You Save: $18.41 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Blower Motor Resistor
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2015-2021 Kia Sedona | 3.3L - Lambda 2 | Wagon Long - 7P, Wagon Long - 8P
View related parts
Kia Sedona Transistor-Field Eff
Part Number: 972351U000
$115.99 MSRP: $168.83
You Save: $52.84 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Transistor-Field Effect; Control Module, Resistor, Transistor
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2015-2021 Kia Sedona | 3.3L - Lambda 2 | Wagon Long - 7P, Wagon Long - 8P
View related parts
Kia Sedona Resistor
Part Number: 971154H000
$44.88 MSRP: $64.77
You Save: $19.89 (31%)
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2006-2014 Kia Sedona | 3.5L - Lambda 2, 3.8L - Lambda | Wagon Long - 7P, Wagon Short - 7P
View related parts
Kia Sedona Resistor-Assembly
Part Number: 0K9A361B11
$47.07 MSRP: $64.30
You Save: $17.23 (27%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Resistor
- Manufacturer Note: W/AIR CON.
- Replaced by: 1K55261C08
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2001-2005 Kia Sedona | Low Grade, Middle Grade | 3.5L | Wagon Short 7
View related parts
Kia Sedona Resistor-Assembly
Part Number: 1K55261C08
$44.56 MSRP: $64.30
You Save: $19.74 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Resistor; Air Tube
- Replaces: 0K20161B11, 0K30B61B15, 0K9A361B11, 1K2A161B11, 1K55261R08, 0K30A61B15
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2001-2005 Kia Sedona | Low Grade, Middle Grade | 3.5L | Wagon Short 7
View related parts
Kia Sedona Transistor-Power
Part Number: 972354D000
$88.29 MSRP: $127.40
You Save: $39.11 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Transistor-Field Effect; Resistor
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2006-2014 Kia Sedona | High Grade, Middle Grade | 3.5L - Lambda 2, 3.8L, 3.8L - Lambda | Wagon Long - 7P, Wagon Long 7, Wagon Short - 7P, Wagon Short 7
View related parts
Kia Sedona Resistor-Assembly
Part Number: 1K55261R08
$47.07 MSRP: $64.30
You Save: $17.23 (27%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Resistor
- Replaced by: 1K55261C08
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2001-2005 Kia Sedona | Low Grade, Middle Grade | 3.5L | Wagon Short 7

Kia Sedona Blower Motor Resistor

The Kia Sedona Blower Motor Resistor controls the speed of the fan so that occupants experience warm or cool air quickly as required. By altering the electricity resistance in the circuit, the component enables the dash controls to transmit selected current to the fan, from delicate air to clearing out the windows blast to a cooling stream. Inside this system, the Blower Motor Resistor is the gatekeeper. It connects the dash heater and A/C knobs to an electronic control module that transmits signals over wiring leads to the motor and forms one crucial chain. When the Blower Motor Resistor, its circuit board, or the connecting wires break, the driver loses partial or complete control of the cabin air and may be aware of fixed speed, erratic bursts, or silent vents. Across every Kia Sedona generation, the Blower Motor Resistor retains the same basic duty and layout, so owners of older Kia vans or the recent Kia people movers will meet no alternate styles but just revised part numbers for specific years. Whether the Sedona rolled off the line in 2005 or the Sedona left the factory, the function remains the same, and swapping out a bad Blower Motor Resistor will immediately restore full command of climate settings.

If you're in search of top-notch, reasonably priced OEM Kia Sedona Blower Motor Resistor, then you've found the perfect spot. Our website boasts an extensive inventory of Kia Sedona Blower Motor Resistor, all priced at the market's premier price. Rest assured, every genuine part we offer comes with a warranty straight from the manufacturer.

Kia Sedona Blower Motor Resistor Parts Questions & Experts Answers

Resistor-Assembly
1K55261C08
Q: How do I remove and install a blower motor and Blower Motor Resistor in a Kia Sedona?
A:
Remove the cable connecting the negative terminal of the battery from the vehicle. Lift the rear console to access the blower motor area and disconnect the blower motor's fasteners and cover if they exist or pull the insulation down at the rear glove box. Remove the electrical connectors that are related to the blower motor power. Note: Cars with self-regulating temperature system employ a power module rather than a blower motor resistor. Both are mounted and joined in similar way. Take off the mounting fasteners and pull the unit out of the heater/air conditioning housing. Removal is the exact opposite of installation. The blower motor and the blower wheel are therefore from the manufacturer in harmony and are fitted only as a unit. The electrical connector of the blower motor should be disconnected. Retrieve the blower motor mounting bolts, then take out the blower motor. Removal is the process of dismantling a system while installation is the opposite of removal. Disconnect/reduce the rear heating and air conditioning housing. Note: All models made in 2006 and later equipped with Power Mosfet and not the blower motor resistor. Both are similar in how they are installed and interfaced. Take off the rear quarter panel trim, and unplug the connector to the blower motor resistor/Mosfet. Take out the mounting fasteners and pull out the unit away from the heater/air conditioning housing. This involves the process opposite to the removal, it involves placing the plant and equipment back at their initial positions. The blower motor and the blower wheel are assembled together at the time of manufacturing and should only be replaced together. Take off the connector that provides power to the blower motor. Take off all the screws that hold the blower motor at the back of the housing. Take off the blower motor from the housing you have identified. Removal: Installation is the exact opposite of removal.