How do you properly replace the front stabilizer bar bushings and links on Kia Sorento?

The wheels of the vehicle should be aligned to the front; then loosened the lug nuts on the front wheels, lift the and support the front of the vehicle using jackstands, then finally remove the wheels and the undervehicle splash shield. On models prior to 2009, unbolt the nuts, washers, and the outside bushings that are situated on top of the sway bar links. Take off the sway bar bushing bracket and the bolts noting the orientation of the bushings. Take out the rubber bushings of the sway bar kit, check for signs of crack or deterioration of the bushings and if evident the bushings must be replaced. Illustration 2 Check if the balljoints are loose and drop them from the lower control arms if mandatory and clean the bushing area of the sway bar kit. Thread the rubber bushings onto the stud ends and position the sway bar kit across the frame; bolt on the bushing blocks, torquing the bolts to the proper figure. Screw the washers and bushings onto the links, swing the bar down over the links and tight the nuts until 1/4-inch of threads remain and that the upper nuts are tightened to the lower nuts. The rest of the installation procedure is proceeded in the reverse sequence of the removal and the lug nuts are tightened to the recommended torque values. On models made from 2011 and onwards remove the sway bar links from the bar, lock the steering wheel to its straight ahead position then place a marks on the relation between the steering shaft and the steering gear before disconnecting the U-joint on the shaft. Place two floor jacks on the subframe and unbolt the subframe mounting bolts and use the jacks to get to the bolts of the sway bar bracket. Wedge the sway bar kit out, check for and repair any cracked or worn out bushing and wipe the bushing area clean. After that, new bushings should be put onto the sway bar kit, and then the bar should be put into the place and the bushing brackets should be installed and tightened to the demanded level of torque. Lift the subframe in relation to the body and fasten the bolts, reconnect the coupling shaft, and then install the links, while tightening the link nuts should not exceed the fixed moment. In this case, follow the reversal process of all the steps that has been made and add the tightening of the lug nuts to the recommended torque.

Genuine Kia Sorento Sway Bar Link

Stabilizer Sway Bar Link

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

21 Sway Bar Links found

View related parts
Kia Sorento Front Stabilizer Link Assembly
Part Number: 54830C5000
$60.88 MSRP: $87.85
You Save: $26.97 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Link Assembly-Front Stabilizer; Link, Stabilizer Link
- Position: Front
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2015-2023 Kia Sorento | 1.6L-Gamma-II, 2.0L - Theta 2, 2.4L - Theta 2, 2.5L-THETA-III, 3.3L - Lambda 2 | Wagon - 5Door 5P, Wagon - 5Door 6P, Wagon - 5Door 7P
View related parts
Kia Sorento Link-Stabilizer
Part Number: 548302W000
$56.20 MSRP: $81.10
You Save: $24.90 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Link, Stabilizer Link
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2013-2014 Kia Sorento | 2.4L - Theta 2, 3.3L - Lambda 2 | Wagon - 5Door 5P, Wagon - 5Door 7P
View related parts
Kia Sorento Link Assembly-Rear Stabilizer
Part Number: 555302B200
$44.69 MSRP: $64.48
You Save: $19.79 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Link, Stabilizer Link
- Position: Rear
- Replaces: 555302B000, 555602J000
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2009-2012 Kia Sorento | 2.4L - Theta 2, 3.5L - Lambda 2 | Wagon - 5Door 5P, Wagon - 5Door 7P
View related parts
Kia Sorento Link-STABILIZER Bar
Part Number: 555803E050
$45.69 MSRP: $62.42
You Save: $16.73 (27%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Link Assembly-Control,RH
- Position: Passenger Side
- Replaced by: 555803E050DS
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2003-2008 Kia Sorento | High Grade, Middle Grade | 3.3L - Lambda, 3.5L, 3.8L, 3.8L - Lambda | 5 Door Wagon, Wagon - 5Door 5P
View related parts
Kia Sorento Link Assembly-Rear Stabilizer
Part Number: 55530C5000
$61.56 MSRP: $88.83
You Save: $27.27 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Link Assembly-Rear Stabilizer,LH; Link, Stabilizer Link
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2015-2020 Kia Sorento | 2.0L - R, 2.0L - Theta 2, 2.4L - Theta 2, 3.3L - Lambda 2 | Wagon - 5Door 5P, Wagon - 5Door 7P
View related parts
Kia Sorento Link Assembly-Rear Stabilizer
Part Number: 555302W000
$67.27 MSRP: $97.07
You Save: $29.80 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Link Assembly-Rear Stabilizer,LH; Link, Stabilizer Link
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2013-2014 Kia Sorento | 2.4L - Theta 2, 3.3L - Lambda 2 | Wagon - 5Door 5P, Wagon - 5Door 7P
View related parts
Kia Sorento Front Stabilizer Link Assembly
Part Number: 548302B000
$50.36 MSRP: $68.80
You Save: $18.44 (27%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Link Assembly-Front Stabilizer,LH
- Position: Driver Side
- Replaced by: 548302B200
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2009-2012 Kia Sorento | 2.4L - Theta 2, 3.5L - Lambda 2 | Wagon - 5Door 5P, Wagon - 5Door 7P
View related parts
Kia Sorento Front Stabilizer Link Assembly
Part Number: 548402B200
$46.69 MSRP: $67.37
You Save: $20.68 (31%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Link Assembly-Front Stabilizer,RH; Link, Stabilizer Link
- Position: Passenger Side
- Replaces: 548402B000
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2009-2012 Kia Sorento | 2.4L - Theta 2, 3.5L - Lambda 2 | Wagon - 5Door 5P, Wagon - 5Door 7P
View related parts
Kia Sorento Link Assembly-Rear Stabilizer
Part Number: 55540C5000
$61.56 MSRP: $88.83
You Save: $27.27 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Link Assembly-Rear Stabilizer,RH; Link, Stabilizer Link
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2015-2020 Kia Sorento | 2.0L - R, 2.0L - Theta 2, 2.4L - Theta 2, 3.3L - Lambda 2 | Wagon - 5Door 5P, Wagon - 5Door 7P
View related parts
Kia Sorento Front Stabilizer Link Assembly
Part Number: 548302B200
$47.68 MSRP: $68.80
You Save: $21.12 (31%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Link Assembly-Front Stabilizer,LH; Link, Stabilizer Link
- Position: Driver Side
- Replaces: 548302B000
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2009-2012 Kia Sorento | 2.4L - Theta 2, 3.5L - Lambda 2 | Wagon - 5Door 5P, Wagon - 5Door 7P
View related parts
Kia Sorento Link Assembly-Rear Stabilizer
Part Number: 555402W000
$66.64 MSRP: $96.17
You Save: $29.53 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Link Assembly-Rear Stabilizer,RH; Link, Stabilizer Link
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2013-2014 Kia Sorento | 2.4L - Theta 2, 3.3L - Lambda 2 | Wagon - 5Door 5P, Wagon - 5Door 7P
View related parts
Kia Sorento Link-STABILIZER Bar
Part Number: 555803E000
$47.78 MSRP: $65.27
You Save: $17.49 (27%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Link Assembly-Control,LH
- Position: Driver Side
- Replaced by: 555803E000DS
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2003-2008 Kia Sorento | High Grade, Middle Grade | 3.3L - Lambda, 3.5L, 3.8L, 3.8L - Lambda | 5 Door Wagon, Wagon - 5Door 5P
View related parts
Kia Sorento Link Assembly-Rear Stabilizer
Part Number: 555302B000
$47.20 MSRP: $64.48
You Save: $17.28 (27%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Position: Rear
- Replaced by: 555302B200
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2009-2012 Kia Sorento | 2.4L - Theta 2, 3.5L - Lambda 2 | Wagon - 5Door 5P, Wagon - 5Door 7P
View related parts
Kia Sorento Link Assembly-Rear Stabilizer
Part Number: 555402W110
$67.27 MSRP: $97.07
You Save: $29.80 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Link Assembly-Rear Stabilizer,RH; Link, Stabilizer Link
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2013-2014 Kia Sorento | 2.4L - Theta 2, 3.3L - Lambda 2 | Wagon - 5Door 5P, Wagon - 5Door 7P
View related parts
Kia Sorento Front Stabilizer Link Assembly
Part Number: 548402B000
$49.31 MSRP: $67.37
You Save: $18.06 (27%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Link Assembly-Front Stabilizer,RH
- Position: Passenger Side
- Replaced by: 548402B200
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2009-2012 Kia Sorento | 2.4L - Theta 2, 3.5L - Lambda 2 | Wagon - 5Door 5P, Wagon - 5Door 7P
View related parts
Kia Sorento Link Assembly-Rear STABI
Part Number: 55530P2000
$59.68 MSRP: $86.12
You Save: $26.44 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Link, Stabilizer Link
- Position: Rear
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2021-2023 Kia Sorento | 1.6L-Gamma-II, 2.5L-THETA-III | Wagon - 5Door 6P, Wagon - 5Door 7P
View related parts
Kia Sorento Front Stabilizer Link Assembly
Part Number: 548113E010
$40.94 MSRP: $55.93
You Save: $14.99 (27%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Link Assembly-Front Stabilizer,LH
- Position: Driver Side
- Replaced by: 548113E110DS
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2003-2006 Kia Sorento | High Grade, Middle Grade | 3.5L | 5 Door Wagon
View related parts
Kia Sorento Link Assembly-Rear Stabilizer
Part Number: 555302W110
$67.27 MSRP: $97.07
You Save: $29.80 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Link Assembly-Rear Stabilizer,LH; Link, Stabilizer Link
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2013-2014 Kia Sorento | 2.4L - Theta 2, 3.3L - Lambda 2 | Wagon - 5Door 5P, Wagon - 5Door 7P
View related parts
Kia Sorento Front Stabilizer Link Assembly
Part Number: 548103E000
$45.69 MSRP: $62.42
You Save: $16.73 (27%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Link Assembly-Control
- Position: Front
- Replaced by: 548103E000DS
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2003-2006 Kia Sorento | High Grade, Middle Grade | 3.5L | 5 Door Wagon
View related parts
Kia Sorento Link Assembly-Rear STABI
Part Number: 55530C5001
$74.34 MSRP: $107.27
You Save: $32.93 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Stabilizer Link
- Position: Rear
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2019-2020 Kia Sorento | 2.0L - R, 2.4L - Theta 2, 3.3L - Lambda 2 | Wagon - 5Door 7P

| Page 1 of 2 |Next >

1-20 of 21 Results

Kia Sorento Sway Bar Link

The Kia Sorento Sway Bar Link maintains the feel of a flat cabin through the turns by linking the stabilizer bar to the suspension to limit the body's lean and improve steering response. Working as the bridge between the sway bar and control arm, the Sway Bar Link will redirect motion from one wheel to the other to keep the weight even when the outside spring compresses. Every generation of the Sorento is reliant upon this little rod with the bushings or ball joints that provide flexibility but maintain stiffness, allowing the stabilizer bar to function correctly. If there is Sway Bar Link wear, clunk, uneven grip, and loose steering, then changing it quickly will allow daily driving to be safe. In normal driving, the front and rear suspension move independently, but once the Kia enters a curve, the bar is twisted, and the Sway Bar Link immediately pulls on the opposite control arm, pulling the body level. Built with sturdy steel, the Sway Bar Link has seen little change over the years of the Kia Sorento sport utility, the main adjustment being the use of stud ends with quieter sealed ball joints in place of simple bushings. High mileage Sorento owners are advised to listen for rattles over bumps as a loose link will allow the bar to vibrate, and Kia drivers will notice a tightening of handling after installation.

If you're in search of top-notch, reasonably priced OEM Kia Sorento Sway Bar Link, then you've found the perfect spot. Our website boasts an extensive inventory of Kia Sorento Sway Bar Link, all priced at the market's premier price. Rest assured, every genuine part we offer comes with a warranty straight from the manufacturer.

Kia Sorento Sway Bar Link Parts Questions & Experts Answers

Front Stabilizer Link Assembly
548402B000
Q: How do you properly replace the front stabilizer bar bushings and links on Kia Sorento?
A:
The wheels of the vehicle should be aligned to the front; then loosened the lug nuts on the front wheels, lift the and support the front of the vehicle using jackstands, then finally remove the wheels and the undervehicle splash shield. On models prior to 2009, unbolt the nuts, washers, and the outside bushings that are situated on top of the sway bar links. Take off the sway bar bushing bracket and the bolts noting the orientation of the bushings. Take out the rubber bushings of the sway bar kit, check for signs of crack or deterioration of the bushings and if evident the bushings must be replaced. Illustration 2 Check if the balljoints are loose and drop them from the lower Control Arms if mandatory and clean the bushing area of the sway bar kit. Thread the rubber bushings onto the stud ends and position the sway bar kit across the frame; bolt on the bushing blocks, torquing the bolts to the proper figure. Screw the washers and bushings onto the links, swing the bar down over the links and tight the nuts until 1/4-inch of threads remain and that the upper nuts are tightened to the lower nuts. The rest of the installation procedure is proceeded in the reverse sequence of the removal and the lug nuts are tightened to the recommended torque values. On models made from 2011 and onwards remove the sway bar links from the bar, lock the Steering Wheel to its straight ahead position then place a marks on the relation between the steering shaft and the steering gear before disconnecting the U-joint on the shaft. Place two floor jacks on the subframe and unbolt the subframe mounting bolts and use the jacks to get to the bolts of the sway bar bracket. Wedge the sway bar kit out, check for and repair any cracked or worn out bushing and wipe the bushing area clean. After that, new bushings should be put onto the sway bar kit, and then the bar should be put into the place and the bushing brackets should be installed and tightened to the demanded level of torque. Lift the subframe in relation to the body and fasten the bolts, reconnect the coupling shaft, and then install the links, while tightening the link nuts should not exceed the fixed moment. In this case, follow the reversal process of all the steps that has been made and add the tightening of the lug nuts to the recommended torque.