What is the location and procedure for installing a knock sensor on Kia Sportage?

An automobile which was manufactured in 1998 until the present time is equipped with a knock sensor. On 1.8L and 2.0L DOHC engines, the knock sensor is located on the right rear side of the engine block. In case of 2.7L V6 engines, each cylinder has its own knock sensor; they are placed under the intake manifold in the valley between the heads. The first step is to jack up the front of your car and support it properly with stands for safety on models having four cylinders. For this job to be done on a 1.8L DOHC engine intake manifold support bracket must be removed. Thereafter disconnect an electrical connector from a knock sensor and remove it with a retaining bolt, if any at all. As for installing a new one, do everything back as you have just undone before but tighten again that retaining bolt safely enough on it now anyways that's if you want not to damage anything else then simply move forward like nothing happened afterward saying "till next time". All these can also be applied to V6 models by removing their upper and lower intakes manifold too after which knock sensors connectors will come out easily in order for them still to have been unscrewed from above or below according whichever part provides better access depending where yours are situated while replacing either knock sensors don't forget tightening them up so thread connections should always hold well when other way around performed so installation will likely go backwards as there's no need really repeating myself over again.

Genuine Kia Sportage Knock Sensor

Engine Knock Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

8 Knock Sensors found

View related parts
Kia Sportage Sensor Assembly-Knock
Part Number: 392502G100
$76.91 MSRP: $110.98
You Save: $34.07 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Knock Sensor
- Replaces: 392502G000
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2010-2022 Kia Sportage | 2.4L - Theta 2 | Wagon - 5Door 5P
View related parts
Kia Sportage Sensor-Knock
Part Number: 3925023500
$65.63 MSRP: $94.70
You Save: $29.07 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Knock Sensor
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2005-2010 Kia Sportage | High Grade, Middle Grade | 2.0L, 2.0L - Beta | 5 Door Wagon, Wagon - 5Door 5P
View related parts
Kia Sportage Sensor Assembly-Knock,RH
Part Number: 3925037100
$68.76 MSRP: $99.22
You Save: $30.46 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor-Knock; Knock Sensor
- Manufacturer Note: RH
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2005-2010 Kia Sportage | High Grade, Middle Grade | 2.7L, 2.7L - Delta | 5 Door Wagon, Wagon - 5Door 5P
View related parts
Kia Sportage Sensor-Knock
Part Number: 392502G700
$49.33 MSRP: $71.18
You Save: $21.85 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Knock Sensor
- Replaces: 392502G200
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2010-2022 Kia Sportage | 2.0L - Theta 2 | Wagon - 5Door 5P
View related parts
Kia Sportage Sensor Assembly-Knock,LH
Part Number: 3925037150
$62.24 MSRP: $89.82
You Save: $27.58 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor Assembly-Knock; Knock Sensor
- Manufacturer Note: LH
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2005-2010 Kia Sportage | High Grade, Middle Grade | 2.7L, 2.7L - Delta | 5 Door Wagon, Wagon - 5Door 5P
View related parts
Kia Sportage Sensor-Knock
Part Number: 0K01D18921
$38.97 MSRP: $56.23
You Save: $17.26 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Knock Sensor
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 1997-2002 Kia Sportage | High Grade, Low Grade, Middle Grade | 2.0L | 2 Door 5 Canvas Top, 5 Door Wagon
View related parts
Kia Sportage Sensor-Knock
Part Number: 392502M500
$30.30 MSRP: $43.72
You Save: $13.42 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Knock Sensor
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2023-2024 Kia Sportage | 1.6L-Gamma-II | Wagon - Long 5Door 5P
View related parts
Kia Sportage Sensor-Knock
Part Number: 392502S000
$84.35 MSRP: $121.72
You Save: $37.37 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Knock Sensor
- Warranty: This genuine part is guaranteed by Kia's factory warranty.
Fits the following Vehicles:
- 2023-2024 Kia Sportage | 2.5L-THETA-III | Wagon - Long 5Door 5P

Kia Sportage Knock Sensor

This Kia Sportage Knock Sensor is one of those components that boost the effectiveness and durability of Kia Sportage automobiles. This is also an advanced sensor that identifies engine knock and reports the same to the power train control module for proper ignition timing. Commonly employing the piezoelectric technology, the Knock Sensor transduces the knock related vibrations into electrical signals to monitor pressure spikes. This capability makes the Kia Sportage functional, especially when using low octane fuels; it will perform well but will not cause engine wear/strain. The recent Kia Sportage models are equipped with developed systems with the help of which it is possible to manage ignition timings for concrete cylinders and to control boost pressure, which brings an additional bonus to density and safety. Affordability also means that the Knock Sensor can be installed in different Sportage models, giving assurance and the optimal experience to the drivers, hence making it unique in the market. In the same manner, the Kia Sportage is also marketed as the one that started introducing safety features with praises that include the "top safety pick" granted by the insurance institute highway safety. Proudly standing for quality and innovation, the Kia Sportage armed with a Knock Sensor stays the benchmark in the SUV classification, ensuring that it may assure the drivers and provide them with memorable and remarkable driving experiences. The Knock Sensor plays a crucial role in maintaining the performance and reliability of the vehicle.

If you're in search of top-notch, reasonably priced OEM Kia Sportage Knock Sensor, then you've found the perfect spot. Our website boasts an extensive inventory of Kia Sportage Knock Sensor, all priced at the market's premier price. Rest assured, every genuine part we offer comes with a warranty straight from the manufacturer.

Kia Sportage Knock Sensor Parts Questions & Experts Answers

Sensor-Knock
3925023500
Q: What is the location and procedure for installing a knock sensor on Kia Sportage?
A:
An automobile which was manufactured in 1998 until the present time is equipped with a knock sensor. On 1.8L and 2.0L DOHC engines, the knock sensor is located on the right rear side of the engine block. In case of 2.7L V6 engines, each cylinder has its own knock sensor; they are placed under the intake manifold in the valley between the heads. The first step is to jack up the front of your car and support it properly with stands for safety on models having four cylinders. For this job to be done on a 1.8L DOHC engine intake manifold support bracket must be removed. Thereafter disconnect an electrical connector from a knock sensor and remove it with a retaining bolt, if any at all. As for installing a new one, do everything back as you have just undone before but tighten again that retaining bolt safely enough on it now anyways that's if you want not to damage anything else then simply move forward like nothing happened afterward saying "till next time". All these can also be applied to V6 models by removing their upper and lower intakes manifold too after which knock sensors connectors will come out easily in order for them still to have been unscrewed from above or below according whichever part provides better access depending where yours are situated while replacing either knock sensors don't forget tightening them up so thread connections should always hold well when other way around performed so installation will likely go backwards as there's no need really repeating myself over again.